Samsung SSA-P401T Uživatelský manuál

SSA-P40x Series

10PRESSInitialize ENDTurn OFF Power..SystemInitializing..Initialize ENDTurn OFF Power• On the process of initializing, the LCD displays as the below•

11• Board ID setting exampleStatus of S/W ON  Not selectedDown S/W to #1  1 (selected)Default Value9. Board ID Setting

12• +12V, 3A DC Power is recommended• Reader is connected to Reader Port #1• Exit Button is connected to Input Port #1• Door Contact is connected to I

13• +12V, 3A DC Power is recommended• Power sources of Relay #1, #3 for connecting lock can be used separatelySSA-P40x / Lock Power11. Wiring Connecti

14• Reader Power sources can be used separately, but GND has to be wired togetherIn the case of not wiring together, due to voltage level difference,

15• Input #1 & #3 are set up for exit button as default value• Input #1 for Door 1 exit button and Input #3 for Door 2 exit button• Input #5 &

16• Input #2 & #4 are set up for door contact sensor as default value( When door is opened longer than setup time, door contact sensor will be act

17SSA-P40x• DOOR LOCK (Power Fail Secure)- Power off  Lock- Power on  UnlockGND-+CathodeAnode1N4004 ~ 1N4007Diode Required+12V• Relay Output #1 &

18SSA-P40x• DOOR LOCK (Power Fail Safe)- Power off  Unlock- Power on  LockGND-++12VCathodeAnode1N4004 ~ 1N4007• Relay Output #1 & #3 are set up

19SSA-P40xGND+-+12VDiode Required• Relay Output #2 & #4 are set up for alarm device as default value• Power is applied then the device for alarm c

2 Intelligent 4 Doors Access Control Panel Dynamic Control of memory up to 50,000 Users / up to 29,500 Event Buffers: 1,000 ~ 20,000 / 30,000 / 40,0

20HOST PCRX(PIN2)TX(PIN3)GND(PIN5)• Direct connection between PC and a SSA-P40x with RS232C• Maximum Communication Cable Length (PC to SSA-P40x) : 15m

21• Internal TCP/IP Module Connection• LAN Cable WiringHOST PC↓1:1 Wiring = CROSS LAN CableHOST PC1:N Wiring = DIRECT LAN CableInternetInternet19. Wir

2220. Block Diagram (SSA-P40x)

23-F1+ READER1 MODE+ READER2 MODE+ READER3 MODE+ READER4 MODE+ DOOR 1 APB+ DOOR 2 APB+ READER1 KEY IN+ READER2 KEY IN+ READER3 KEY IN+ READER4 KEY IN+

24F1READER1 MODERF ONLY (Default)RF + PASSWORDREADER1 T/S00 ~ 15READER2 MODERF ONLY (Default)RF + PASSWORDREADER2 T/S00 ~ 15READER3 MODERF ONLY (Defau

25TIME SETTING12/34 12:34:56-F1+ READER1 MODE+ READER2 MODE+ READER3 MODE+ READER4 MODE+ DOOR 1 APB+ DOOR 2 APB+ READER1 KEY IN+ READER2 KEY IN+ REA

26F2TIME SETTINGYYYYMMDDhhmssWYYYY: Year, MM: Month, DD: Datehh: hour, mm: minute, ss: secondW: 1-SUN, 2-MON, 3-TUE, 4-WED, 5-THU, 6-FRI, 7-SATHOLIDAY

27F2IN/OUT DEFINE(1. ~ 7.) iTDC INPUT #1 ~ #7(8. ~ 15.) EIO INPUT #1 ~ #8(16. ~ 19.) DURESS MODE 1 ~ 420. Output T/S21. INPUT T/S22. INPUT TYPE(23. ~

28ID REGISTRATION-F1+ READER1 MODE+ READER2 MODE+ READER3 MODE+ READER4 MODE+ DOOR 1 APB+ DOOR 2 APB+ READER1 KEY IN+ READER2 KEY IN+ READER3 KEY IN+

29F3ID REGISTRATIONID 8 Digit (SSA-P401 : 10 Digit), PASSWORD 4 Digit, CODE 2 Digit, TA 00 ~ 15, TB 00 ~ 15, TC 00 ~ 15, TD 00 ~ 15RA 0/1, R

3Model SSA-P400 SSA-P400T SSA-P401 SSA-P401TCPU 8bit MicroprocessorMemoryProgram Memory 64KByte ROMData Memory 512KByte Flash MemoryUserUsers and Even

30VERSIONSSA-P40x : V7.0.0-F1+ READER1 MODE+ READER2 MODE+ READER3 MODE+ READER4 MODE+ DOOR 1 APB+ DOOR 2 APB+ READER1 KEY IN+ READER2 KEY IN+ READER3

31F4Firmware Version SSA-P40x V7.0.0RAM TEST Memory TestOUTPUT TEST OUTPUT 1 ~ OUTPUT8LCD TEST LCD MODULE TESTKEYPAD TEST 0123456789ABCDEFREADER TEST

43. System Configuration (1/2)

5No Description Cable Specification Max. Distance①Power (DC12V)DC Power  SSA-P40xBelden #9409, 18 AWG2 conductor, unshielded30m②Reader (Power and Dat

6• Not connect both ends of shield wires to the grounding system(In the case of connecting both ends, there will be a current flow through the shield

7Input port#1 ~ #732#7Reader port#1 ~ #44#1#4#1Board ID S/W1Initialize S/WTCP/IP moduleconnecterLCD display port Keypad portRS422 PortRS232 PortTCP/IP

8Part Names Functions1 BOARD ID S/WThis BOARD ID S/W is for communication ID setting of SSA-P40x. As the device number(000 to 255) that is set by the

9Part Names Functions1 Relay Output Port #5 ~ #12 These are 8 Relay Output ports2 Input Port #1 ~ #7 These are 8 Input Ports (8 LEDs indicate input st