Samsung SRP-372 Uživatelský manuál

User's Manual Ethernet Interface Rev. 5.00 SRP-270 SRP-275 SRP-280 SRP-350 SRP-350plus SRP-370 / 372 SRP-770 / 770II SLP-T400 http://ww

Ethernet Rev. 5.00 - 10 -6) Set Inactivity Time as ‘0’. [Note] - Default value is 0. Choose from 0 to 32767. - When you set Inactivity time, Ether

Ethernet Rev. 5.00 - 11 -8) When setting finishes, click Setting. [Note] Successfully finished set up Unsuccessfully finished set up - Whe

Ethernet Rev. 5.00 - 12 -6-2. DHCP interface set up 1) Turn on the printer. 2) Execute Configure Tool. [Note] - Use proper Configuration Tool

Ethernet Rev. 5.00 - 13 -4) Select MAC Address in Board list and check at DHCP Mode. [Note] - If many MAC addresses appear, refer to the MAC add

Ethernet Rev. 5.00 - 14 - 6) When setting finishes, click Setting. [Note] Successfully finished set up Unsuccessfully finished set up -

Ethernet Rev. 5.00 - 15 -8) Click Search to check given IP. 9) If the given IP is OK, click Exit.

Ethernet Rev. 5.00 - 16 -6-3. Firmware update 1) Turn on the printer 2) Execute Configure Tool. [Note] - Use proper Configuration Tool dependen

Ethernet Rev. 5.00 - 17 -4) Select MAC Address in Board. [Note] - If many MAC addresses appear, refer to the MAC address on the label of the int

Ethernet Rev. 5.00 - 18 -[Note] - Check the extension of the file, which should be “bin”. Successfully finished F/W update Unsuccessfully finishe

Ethernet Rev. 5.00 - 19 -7. Web Server 7-1. Static IP interface set up 1) Execute Internet Explorer. 2) Enter IP address of the printer at Address

Ethernet Rev. 5.00 - 2 - Table of contents 1. Interface setting Guiding...

Ethernet Rev. 5.00 - 20 -[Note] - If you are not aware of Subnet Mask, refer to the below. - When the IP address is (1) 1~126.xxx.xxx.xxx: Subnet Mask

Ethernet Rev. 5.00 - 21 - 6) Set baud rate (Serial speed). [Note] - The baud rate (Speed) should be same as the baud rate of the printer. - The ba

Ethernet Rev. 5.00 - 22 -8) If you click the message, you can check your configuration setting. [Note] - If any change was not found after setting

Ethernet Rev. 5.00 - 23 - (4) Check for newer version of stored pages → Click Every visit to the page. (5) Click Refresh in Internet Explorer. 7-

Ethernet Rev. 5.00 - 24 -7-3. Firmware update 1) Click Firmware update. 2) Internet Explorer is executed and it moves to download site automatical

Ethernet Rev. 5.00 - 25 -3) Download Configure_Vx.xx.zip file and *.bin file. [Note] - You can download it by double-clicking icons or co

Ethernet Rev. 5.00 - 26 -8. Ethernet test by using Windows test page If you don’t have any test program to check printer’s performance, you can use W

Ethernet Rev. 5.00 - 27 -4) Select Ports tab. 5) Click Add Port.

Ethernet Rev. 5.00 - 28 -6) Select Standard TCP/IP Port and click New port. 7) When standard TCP/IP printer add wizard window pops up, click Next.

Ethernet Rev. 5.00 - 29 -9) Click Next. [Note] - Click Next without any selection nor change. 10) Click Finish. 11) Click Close to close P

Ethernet Rev. 5.00 - 3 - How to install (Page 5) Check Network (Page 32) Static IP?DHCP Static IP Interface set up (Page19) Y NCheck the Interfa

Ethernet Rev. 5.00 - 30 -12) Click Configure Port. 13) Enter same port number as the value of Local Port of the Ethernet interface at Raw Setting

Ethernet Rev. 5.00 - 31 -14) Click OK. 15) Select General tab and click Print Test Page to check if the printer works properly.

Ethernet Rev. 5.00 - 32 -9. How to check Static IP or DHCP 1) Start > Control panel > Network Connections 2) Select: “Local Area Connection

Ethernet Rev. 5.00 - 33 -4) Click “Properties”. 5) Information of network registration with Static IP 6) Information of network registration wi

Ethernet Rev. 5.00 - 34 -10. Factory Reset 1) Default setting after factory reset - Activate DHCP mode - Local Port: 9100 - Inactivity Time:

Ethernet Rev. 5.00 - 35 -11. Function Key set up 1) How to use (1) Turn on the printer (2) Wait 10 or more seconds until the Ethernet interface boo

Ethernet Rev. 5.00 - 36 -[Appendix 1] Details of interface card Item Details Network interface 10/100 Base-T All in one (Auto detection) Protocol

Ethernet Rev. 5.00 - 37 -[Appendix 3] Setting up serial communication 1) Printer DIP switch set up Printer Baud rate & DSW set up Handshaking

Ethernet Rev. 5.00 - 38 -2) Set the baud rate (Serial speed) - SRP-270,275,280: Max. 19200 bps - SRP-350: Max. 57600 bps - SRP-350Plus: Max. 115200 b

Ethernet Rev. 5.00 - 4 - 2. Manual Information The purpose of this manual is to provide information on the operation and usage instructions of the Eth

Ethernet Rev. 5.00 - 5 - 4. How to install 1) Check the interface version [Note] - Each version uses its own Configuration Tool. 2) Turn of the pr

Ethernet Rev. 5.00 - 6 - 5. Specifications 5-1. Hardware version Hardware version is marked on the label on the interface card bracket. IFA-E TYPE (V

Ethernet Rev. 5.00 - 7 - 6. Configuration Tool 6-1. Static IP interface set up 1) Turn on the printer. 2) Execute Configure Tool. [Note] - Use

Ethernet Rev. 5.00 - 8 - [Note] - If Windows Security Alert pops up, please press Unblock. 4) Select MAC Address in Board list and set up Network

Ethernet Rev. 5.00 - 9 - - If you are not aware of Subnet Mask, refer to the below. When the IP address is (1) 1~126.xxx.xxx.xxx: Subnet Mask: 255.0.0