Samsung MIM-F00N Uživatelský manuál

DVM CHILLERInstallation manualFCU Application KIT MIM-F00N • Thank you for purchasing this Samsung Product. • Before operating this unit, please read

10CHECKING BEFORE THE INSTALLATIONChecking before the installationyyFCU interface module should be installed inside of FCU KIT.yyDMS2.0 is not support

11CHECKING BEFORE THE INSTALLATIONyyFCU KIT and FCU interface module is for integrated control of FCU with DVM CHILLER by DMS 2.5.yyMaximum number of

12INSTALLATIONFCU KIT installationFCU KIT installation1 Check the location of FCU KIT installation.yySelect the installation location that FCU can be

13INSTALLATIONyyWater sensor should be attached to inlet pipe (1) for 2 pipe system (Water In), and each inlet pipe (2) for 4 pipe system (Cooling pip

14INSTALLATIONFCU KIT installationInstall FCU KIT where the weight load of the product can be supported.200(7.87)270(10.62)225(8.85)200(7.87)FCU inter

15INSTALLATIONWiring workConnecting a power cable and communication cableyyMake sure to cut-off the power before connecting the power cable.yyThe powe

16INSTALLATION CAUTION• The circuit diagram on the cables as shown above represents only outline and it does not describe detailed instruction on the

17INSTALLATIONSelecting solderless ring terminal1 Select the solderless ring terminal depending on the nominal dimension of the power cable.2 Cover

18INSTALLATIONFCU KIT power cable specicationThis specication is when installing a FCU KIT.EuropePower supply Power cable Ground wire Communication

19INSTALLATIONFunctions of FCU KITyyFan control (Auto, High, Mid, Low), valve control, setting indoor temperature, sensing inlet water pipe temperatur

2ContentsPREPARATION 3Safety precautions 3CHECKING BEFORE THE INSTALLATION 7Checking before the installation 7Accessories 7Net dimension 7Name of

20INSTALLATIONyyPower cable: Conduit and Conduit tting (1/2") work by installeryyWater valve: Conduit and Conduit tting (1/2") after separ

21INSTALLATION WARNINGyyBe sure to use the conduits and conduit ttings when extracting the wires for safety. NOTE• Arrange communication cables (F1,

22INSTALLATION2 Sensor connection by FCU typeyyInstall water pipe sensor at inlet within 1 m from FCU.yyConnect the sensor after checking the install

23INSTALLATIONPipe type Location of Sensor Connector Location of pipe2-pipe Water-IN 1 Water inlet pipe4-pipeWater-IN 1 Chilled water inlet pipeWater-

24INSTALLATION4 External contact connectionyyIn case of connecting external contact, set SEG14 of installation option according to the table.External

25INSTALLATION5 Option room sensor (Model: MRW-TA)yyIn case of installing room sensor as option, set installation option according to the table. (05s

26INSTALLATION7 Optional external contact interface module (MIM-B14)yyIf you need an external contact control (for indoor unit ON/OFF, external heate

27INSTALLATIONSensorPipe2 Stick the sensor to the pipe. CAUTIONAttaching sensor• Attach the sensor where temperature sensing is performed best.• St

28SETTINGProcedure of option settingyySetting address of FCU KIT and installation option is set by remote controller option. It is also possible by wi

29SETTINGStep 2. Procedure of option settingAfter entering the option setting stage, select the option as shown below. CAUTION• 24 digits are availab

3PREPARATIONThese safety precautions are for owner’s safety and preventions of property damage. Therefore, please read this manual thoroughly before i

30SETTINGStatus Setting an optionSEG4 SEG53 Setting SEG4, SEG5 optionPress [Fan∨] button to enter SEG4 value.Press [Fan ∧] button to enter SEG5 value

31SETTINGStatus Setting an optionSEG11 SEG129 Setting SEG11, SEG12 optionPress [Fan∨] button to enter SEG11 value.Press [Fan ∧] button to enter SEG12

32SETTINGStatus Setting an optionSEG18 SEG2015 Setting SEG18, SEG20 optionPress [Fan∨] button to enter SEG18 value.Press [Fan ∧] button to enter SEG2

33SETTINGStep 3. Procedure of option settingAfter option setting is complete, press the [Mode] button to check whether the setting value is correct or

34SETTINGSetting address (MAIN/RMC) of FCU KIT1 Check if power is supplied to FCU KIT.yyWhen the power is not supplied to FCU KIT, there should be ad

35SETTING CAUTION• Main address (SEG5 ~ SEG6) can be set in range of 0 ~ 47.• When using automatic address setting, FCU interface module automatical

36SETTING02 series installation optionSEG1 SEG2 SEG3 SEG4 SEG5 SEG60 2-Fan control when Thermo OffCentral control -SEG7 SEG8 SEG9 SEG10 SEG11 SEG121Se

37SETTINGOption No. : 02XXXX-1XXXXX-2XXXXX-3XXXXXOption SEG1 SEG2 SEG3 SEG4 (*1) SEG5 SEG6Description Page Mode - Fan control when Thermo Off Use of c

38SETTINGOption SEG13 SEG14 SEG15 SEG16 (*3) SEG17 (*4) SEG18 (*5)Description Page Use of external controlSetting the output of external controlOperat

39SETTING(*4)• [Cool mode] – Err= Indoor temperature – Set temperature – If Err > C+2, the modulating valve operates at the maximum voltage dened

4PREPARATIONDo not install this product near a heater, inammable material. Do not install this product in a humid, oily or dusty location, in a locat

40SETTINGOption No. : 05XXXX-1XXXXX-2XXXXX-3XXXXXOption SEG1 SEG2 SEG3 SEG4 SEG5 SEG6Description Page ModeUse Auto Change Over for 4-pipe only(When se

41SETTINGOption SEG13 SEG14 SEG15 SEG16 SEG17 SEG18Description PageFCU KIT pipe installation structure-Valve open control when Thermo Off-FCU cool air

42SETTINGyyWarm air prevention in cooling – Room < Water-IN temp. (°C) - 1 °C: Fan Off – Room > Water-IN temp. (°C): Fan On• In case of using e

43SETTINGChanging a particular optionYou can change each digit of set option.Option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6Description Page Mode Option mode to

44OTHERSError codeOperation and error status can be checked by LED of FCU KIT.Error code R-LED Y/G-LED Error Solutions162ON OFF EEPROM error Change EE

OTHERS45Checking FCU KIT installationyyCheck if FCU KIT is installed properly. – Check if cables of FCU KIT are properly connected. – Check if FCU KIT

46OTHERS CAUTIONSolution for mixed operation prevention• This function is to prevent DVM CHILLER and FCU (KIT) from operating in different modes. – E

OTHERS47DisplayyyThe following function of FCU KIT can only be used when using wired remote controller. – Operation On/Off – Auto/Cool/Fan/Heat mode

OPTION FCU KIT_IBIM_06104A-01_EN.indd 2 2017-03-07 오후 1:14:29

5PREPARATIONFor power supply WARNINGDo not pull or excessively bend the power cord. Do not twist or tie the power cord. yPotential risk of electric sh

6PREPARATIONDo not operate the product with wet hands. yThere is risk of electric shock.Do not spray volatile material such as insecticide onto the pr

7CHECKING BEFORE THE INSTALLATIONChecking before the installationAccessoriesNamePipe temperature sensor [10 m(32.8 ft)]Aluminum tape Rubber tape M4x16

8CHECKING BEFORE THE INSTALLATIONName of the partsUpper coverFCU KIT PBALower baseSpare holesChecking before the installationOPTION FCU KIT_IBIM_06104

9CHECKING BEFORE THE INSTALLATIONDiagram of DMS 2.5 and DVM CHILLER & FCUCN4CN3REDCN2BLKYELREDY-GRNCN4CN3REDCN2BLKYELREDY-GRNDMS2.5 (MIM-D01AN)Con