Samsung SCC-C6403P Manuál s instrukcemi

SmartDome CameraSCC-C6403PPart : AB68-00571A(00)EDFEsIOwner’s InstructionsBenutzerhandbuchManuel d’instructionManual del usuarioIstruzioni per l’uso00

2-3 2-4E1. First, connect one end of the BNC video cable connector tothe Video Output Terminal (VIDEO OUT)2. Then, connect the other end ofthe connect

2-6E2-53) INDOOR HOUSING (SHG-120)This housing is used for installing the SmartDome Camera to an indoorwall or a ceiling.4) OUTDOOR HOUSING (SHG-220)T

2-8E2-71. [Figure 1] Install the structure on theceiling.(Refer to Installation reference for the Length of the structure)* Built in by the builder of

3-1E2-9Chapter 3 Setup Menu OverviewIn this chapter, we will look over the Setup Menu of the SCC-C6403P, First we'll look over the overall struc

3-3E3-2The diagram shown above illustrates the overall structure of the Setup Menu.In this section, a description of the Setup menu features will enab

3-5E3-4Use the controller to press the MENU selection key and the followingscreen will be displayed.In case of ➀, use UP/DOWN/LEFT/RIGHT/[ENTER] key f

3-7E➜Press [Enter]MOTION DETIn MOTION DET, you can set the Motion Detection function, Motion DetectionSensitivity, and the Area of Motion Detection.

DISPLAY ZOOMIn DISPLAY ZOOM, you can display the ZOOM scale on the screen.❈ If no change on the ZOOM scale is made for 3 seconds, the information wind

3-11E3-10For items in the BLC menu, the user can set the size and location of theBLC area by pressing [ENTER] key after put the cursor on USER… usingt

3-13E(VIDEO SET)IRIS ALC...SHUTTERAUTO X2...MOTIONF.FASTWHITE BAL ATW1 DIS ---FOCUS MODE ONEAFSPECIAL ...EXIT QUITAGCThe AGC menu w

ESafety PrecautionsImportant Safety InstructionsThe purpose of this information is to ensure proper use of this product toprevent danger or damage to

3-15EYou can select one of four modes for white balance adjustment as follows:- ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, thecolor

3-17E3. PRESETThis is the menu that user sets the PAN/TILT location, Zoom/Focus, andscreen condition, so the camera can monitor the presetting area on

3-19E4. ZONE SETThe ZONE SET menu includes the setup of ZONE DIRECTION, andZONE AREA.➜Press [Enter](ZONE SET)ZONE DIR SET OFFZONE AREA SET

3-21E3-20ZONE AREA SET 0LOCATION ...ZONE ID SET ...ZONE ENABLE ONEXIT QUITZONE ID SETThis function is

3-23E3-22SPEEDThis is a setting function for movement speed setup. It can be set fromSTEP1 to STEP64.DWELL TIMEThis is a function for setting up the

3-25E3-24AUTO PLAYAUTO PLAY executes SCAN, AUTO PAN, PATTERN, and PRESET when thereis no camera action after AUTO RETURN finishes.AUTO RETURNThis menu

3-27E3-267. OTHER SET PROPORTIONAL P/TThis function controls the PAN/TILT speed to the ZOOM magnificationratio during the manual operation of PAN/TILT

3-29E3-28➜Press [Enter]** MAIN MENU ** CAMERA SET...VIDEO SET...PRESET...ZONE SET...AUTO SET...ALARM SET...OTHER SET...SYSTEM INFO...( SYSTEM INFO)ALA

3-31E3-309. SHORT KEYSSSC-1000 or SSC-2000 Controller supports the following short keys.Other keys than AUTO CAL. and AUTO RETURN, upon execution, sha

3-32Contents- Zoom lens single body SmartDome CAMERA- AC 24 ± 10% (50Hz ± 0.3Hz)- 18W- PAL STANDARD COLOR SYSTEM- 1/4 inch 410K IT Type S-HAD CCD- 752

6. Do not place conductive objects (e.g., screwdrivers, coins, and metal things) or containers filled with water on top of the camera. (Doing so mayca

1-2E1-1Before UsageThis is a basic instruction manual for the SCC-C6403P user. It contains all the instructions needed to use the SCC-C6403Pfrom a si

1-3 1-4EIn this chapter we will briefly introduce the SCC-C6403Pand show main functions, locations of control and SwitchSetting.Chapter 1 SCC-C6403P

1-6E1-5Locations of ControlFRONTSCC-C6403P IntroductionSCC-C6403P is a zoom lens built in smart dome camera whichprovides you with the best monitoring

1-8E1-7ADAPTER CONNECTIONSCC-C6403P Adapter BOARDAC 24V OUTPOWERAC 24V OUTPOWERBACK00571A-SCC-C6403P-ENG 8/17/06 1:53 PM Page 1-7

1-10E1-9Setting RS-422A/RS-485 termination12As it is shown in the structure map, when Controller and RS-422A/RS-485 is connected it should be terminat

2-2E2-1Before InstallingChecking Package ContentsPlease check that all components listed below are included in thepackage:SCC-C6403Bracket anchorAC 24