Samsung WF203ANW Uživatelský manuál stáhnout pdf

Fast Track Troubleshooting

Model:

WF203ANS/XAA

WF203ANW/XAA

Quick Test Mode

Note: This test erases all faults and memory:

To enter press Spin, Soil, & Power

simultaneously with the power off.

1. All LED’s light up and the washer beeps as it

enters the Quick Test Mode.

2. The unit displays the software version for a

second then clears the EEprom.

3. After the displaying the software version, LCD

will display Model information. If EEEE is displayed

the PCB ass’y is defective.

4. When the version is displayed. Press the follow-

ing keys to test the various components

Press Temp Key to cycle through the Water Valves in

this order: Cold Main, Bleach, Cold Main & Bleach for

Fabric Softener, Hot, then off.

Press Spin Key to test Motor circuit.

Press Signal Key to test Drain Pump

Press Soil to test door lock - unlock circuit

Service Mode: (Can be entered while operating)

This mode allows more detailed operation tests and trouble-

shooting, to enter press Signal & Extra Rinse simultaneously

with the power on.

While in Service Mode the following tests can be performed:

Quick Spin Test = Delay Start & Spin: This accelerates the

drum motor from 0 to maximum RPM over a few minutes.

Note: Stay with the washer during this test, out of balance

detection is bypassed and the door may not lock. Press the

Start/Pause button during the test to hold its spinning speed for

10 minutes before going back to Quick Spin Test Mode

Cycle Count = Press the Signal button to see how many times

the unit was used

Soft Ware # = Press Soil button shows software version

Fast Time Down = Press Temp button to advance to next cycle

Fault Code Test = Press the Spin button to view the stored fault

codes – then turn Dial to view error codes (Push Start/Pause

while the code is displayed to view the number of cycles since the

error occurred)

Peripheral (Main PCB) input Tests

1. Extra Wash

. Then turn the Dial so that the Normal is turned

on. Next, press the Start/Pause Key. The Water Temperature will

be displayed in Fahrenheit.

2. Extra Wash

. Then turn the Dial so that the Whites is turned

on. Next, press the Start/Pause Key. The door status will be dis-

played (OP if open, CL if closed).

3. Extra Wash

. Then turn the Dial so that the Perm Press is

turned on. Next, press the Start/Pause Key. The door lock Switch

status will be displayed (UL if unlocked, Lo if locked).

Water Frequency/Water Sensor Testing

Select a cycle & start the washer, enter Service Mode &

press Extra Wash.

Turn the Dial so that the Quick Wash is turned on. Next, press

the Start/Pause Key. The Water Frequency will be displayed. The

frequency will change as the unit fills.

IMPORTANT SAFETY NOTICE – “For Technicians Only” This service data sheet is

intended for use by persons having electrical, electronic, and mechanical experience

and knowledge at a level generally considered acceptable in the appliance repair trade.

Any attempt to repair a major appliance may result in personal injury and property

damage. The manufacturer or seller cannot be responsible, nor assume any liability for

injury or damage of any kind arising from the use of this data sheet.

EEPROM Clear Check

Power off, Press Delay Start, Signal and Power Key at

the same time. Good = Good Fail = FAiL

All memory will be cleared, including Fault Codes

This should be done when a new Main PCB is

installed

SUPPORT INFORMATION

Training — Plus One http://my.plus1solutions.net/clientPortals/samsung/

Help — GSPN http://service.samsungportal.com/

Samsung Product Support TV http://support-us.samsung.com/spstv/howto.jsp

Customer information videos and chat programs. Programs for Fridges, Laundry, Ranges & D/W

Publication # tsWF203 Revision Date 02/15/2011

1 2 3 4 5 6 7

Fast Track Troubleshooting 1

Shrnutí obsahu

Strany 1 - Fast Track Troubleshooting

Fast Track Troubleshooting Model: WF203ANS/XAA WF203ANW/XAA Quick Test Mode Note: This test erases all faults and memory: To enter press

Strany 2

WF203

Strany 3

CN9 1 Motor Pwr U Phase (Blu) 2 Motor Pwr V Phase (Wht) 3 Motor Pwr W Phase (Red) CN10 1 Main Valve (Blu) 2 Hot Valve (Red) 4 Bleach Valve (Pnk) 6 Dr

Strany 4

Door Lock Check Test 1 Test 2 Connector CN10 Pin 7 (Sky Blue) and CN5 Pin 3 (Blue) When Door is Locked or Unlocked there is a pulse of 120VAC for a f

Strany 5

Error Type Error Mode Details LED LCD Drain Error nD 1 Chec

Strany 6

When installing a washer and dryer on the first, or second floor, do not exceed this leg adjustment height for stability. Foot Pad for Walking Washer,

Strany 7

Water valve connections for the Detergent Drawer Laundry Touch Up Paints Items Packed With Washer BOLT-SPANER (10-13mm Wrench) DC60-40146A ASSY HOSE W