Samsung SV-2000DS Uživatelský manuál stáhnout pdf

LIGHT SOURCE

INSTALLATION GUIDE

INSTALLATION

• General Requirements

• Fiberhead Installation

MAINTENANCE

• Lamp & Fuse Replacement

• Troubleshooting

APPENDIX

• Specifications

• Warranty

General Information

1. Have proper voltage at site. Voltage requirements for light sources may be specified at time of order. (Refer to

figure on this page for power requirements or refer to the label on the back of the illuminator.)

2. Mount the light source in an area that has good ventilation and clearance for fan intake and exhaust. Avoid

placing multiple illuminators in positions that place air exhaust and air intake vents near each other.

3. Avoid dusty areas.

4. Be sure the mounting location will allow access for bulb replacement and that there is enough clearance for the

light source lid to be opened.

5. The mounting location must be a minimum distance from water, based on local, county or state building codes.

Use GFI circuit breakers when installing near water.

6. For mounting use #10 screws or bolts.

7. CAUTION: Do not turn key switch to ON position when lid is open.

8. Do not operate without lamp in place. Allow lamp to cool before removing. Replace with lamps supplied by

SUPERVISION® International, Inc. or authorized SUPERVISION® distributor.

ISM

1997

1 2 3 4 5 6 ... 11 12

Shrnutí obsahu

Strany 1 - INSTALLATION GUIDE

LIGHT SOURCEINSTALLATION GUIDEINSTALLATION• General Requirements• Fiberhead InstallationMAINTENANCE• Lamp & Fuse Replacement• TroubleshootingAPPEN

Strany 2 - TOP VIEW

UL/cUL Listed for Dry LocationsInput Voltage/Current• 120 VAC. 60Hz / 1.8 Amps• CE: 220-240VAC, 50Hz. / 9 Amps• 277 VAC, 60Hz / .8 AmpsLamp• 150 Watt

Strany 3

WarrantyCompany _____________________________________________________________Contact ______________________________________________________________Add

Strany 4 - Capacity: 500 fibers

FIRSTCLASSPOSTAGE8210 Presidents DriveOrlando, Florida 32809U.S.A.

Strany 5 - Capacity: 300 fibers

color wheel motorpowerHotNeutralGroundblackgreenwhiteyellow wireAdd switch to controlcolor wheel start/stop:1. Turn off power2. Cut yellow wire3. A

Strany 6 - Lamp Replacement for sv.250H

TOPBOTTOM1" brackets30.2cm(12")5"13.25" (center of holes)KeyswitchFiber head2.5"(holes)0.5"Air exhaust louvre(must face

Strany 7 - AUTO ON/OFF

sv.750INSTRUCTIONS:CAUTION: Do not allow the black jacket portion of Endglow cables to come into the fiber tightconnector portion of the fiberhead.

Strany 8

INSTRUCTIONS:CAUTION: Do not allow the black jacket portion of Endglow cables to come into the fiber tight connector portion of the fiberhead.The bla

Strany 9 - Specifications for sv.250H

STEP 11. Turn off power, open cover.2. Remove lamp cover screw (A) with phillipsscrewdriver.CAUTION: Do not touch bulb when hot. Letcool down befor

Strany 10 - Specifications for sv.2000D

FUSECDAUTO ON/OFFSWITCHFANlampreflectorelectricalconnectorsclip holderASTEP 11. Turn off power, open cover.2. Pull lamp reflector out of clip holder

Strany 11 - WARRANTY REGISTRATION

Illuminator will not operate:Make sure illuminator is wired properly.Make sure the power switch on the back of the light source is in the “up” positio

Strany 12 - Orlando, Florida 32809

UL Listed for Wet LocationsInput Voltage/Current• 120 VAC. 60Hz / 1.8 Amps• CE: 220-240VAC, 50Hz, .9 AmpsLamp• 250 Watt Halogen MR-16 ELC• 600 average

Komentáře k této Příručce

Žádné komentáře

Samsung SV-2000DS Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Světlomety Samsung SV-2000DS. Light Source Install Guide Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce